null

Bond Kote Resin

$169.00
(1 review) Write a Review
SKU:
40-PBBK5
UPC:
637509171803
Condition:
New
Availability:
In Stock
Weight:
50.00 LBS
Shipping:
Free Shipping

Description Hide Description- Show Description+

5 Gal Container
Liquid Resin.

You need 5 Gal Bond Kote Resin per 2 Bags.

SGM Bond Kote is a specially formulated two part cementitious coating, designed to be used as an ideal substrate to mechanically bond pool plaster over existing plaster finishes.

CHARACTERISTICS:

• Superior bonding capability 
• High flexural strength 
• Eliminates excessive substrate preparation 
• Virtually eliminates delamination problems 
• Saves labor and equipment costs 
• Provides even dry time while plastering

LIMITATIONS:
All materials and surfaces to be coated should remain between 40 degrees F/120 degrees F 24 hours prior and 24 hours after installation. Do not apply in rain or extremely high humidity. Protect "Liquid Resin" from freezing. Plaster should be applied to Bond Kote within 14 days or reapply Bond Kote. DO NOT USE OVER PAINTED OR PLASTIC FINISHES.

PACKAGING:
SGM Bond Kote is formulated in units consisting of two 65 lb. bags of a factory blended dry cement mix and one 5 gallon container of "Liquid Resin". These ingredients are mixed at jobsite as per mixing instructions.

SURFACE PREPARATION:
Check completely for hollow areas and remove all loose plaster. Remove all mildew, algae, fungus and rust by either sand blasting or with an acid wash which must be followed by neutralization with soda ash. If surface is unusually soft, painted, peeling or flaking, then surface must be heavily sanded or water blasted. Regardless of method used, thoroughly wash down with "jet nozzle" hose and let pool drain until there is no standing water present. NOTE: Special attention is required on pools below water table and or leaking.

MIXING:
• Make sure "liquid resin" is mechanically agitated before use to disperse all settled solids. 
• Then pour "liquid resin" (5 gallon) into a clean mixing container with flat bottom. Add Bond Kote (two 65 lb. bags) while continuously mixing with echanical mixer. Continue mixing for 2-4 minutes until Bond Kote is completely dispersed. NEVER USE LESS 
• THAN 115 lbs. OF DRY MIX PER 5 GALLONS OF LIQUID RESIN.

APPLICATIONS:
To check consistency of material, apply Bond Kote with 1-1/4" nap roller onto a vertical test area. Let material set for 1 minute; then, using a clean textured roller, rough up surface to desired finish. Material thickness can be adjusted by adding a small amount of "cement mix" if too thin or "liquid resin" if too thick, adjust only 1 time. DO NOT RETEMPER MIX. Once Bond Kote is mixed to correct consistency, apply immediately, do not let material stand unused. Apply, mixed Bond Kote with 1-1/4" nap roller to steps at shallow end of pool and let material set for approximately 1 minute; then, rough up surface to desired finish with clean textured roller as done in test area. Continue this same process with the wall areas and then proceed to the floor surface last. Starting at deep end of pool make sure application is uniform in thickness and texture.

CURING:
Minimum cure is reached in 6 hours; setting and drying time may vary according to atmospheric conditions. For best results wait 24 hours before plastering.

PLASTERING:
Mist Bond Kote with clean cool water prior to plastering to permit proper hydration. Make sure Bond Kote is free of any foreign matter before plastering.

COVERING:

One unit covers 450-500 square feet of surface area.

CLEAN UP/STORAGE:
Clean hands, tools and containers with warm soapy water.

NOTE: USE NEW ROLLER WITH EACH APPLICATION.

*Free Shipping Only in Soth Florida*

Warranty Information Hide Warranty- Show Warranty+

SGM, Inc. warrants this product will perform in accordance with its intended use for a period of one year from the date of manufacture. Any claim for defective products must be submitted in writing to SGM, Inc., and samples of the defect must be provided. EXCEPT AS PROVIDED HEREIN, SGM, INC. MAKES NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. IN NO EVENT SHALL SGM, INC. BE LIABLE FOR DAMAGES OF ANY KIND OR NATURE, WHETHER ARISING BY CONTRACT, TORT OR OTHERWISE. SGM, INC.’S SOLE OBLIGATION WILL BE TO REPLACE ANY PRODUCT DETERMINED BY SGM, INC. TO BE DEFECTIVE.

Videos Hide Videos- Show Videos+

1 Review Hide Reviews- Show Reviews+

  • 5
    satisfied

    Posted by Wendy on Nov 30th 2020

    I was totally satisfied once again with their service.

Subscribe to our newsletter

Get the latest updates on new products and upcoming sales

No thanks